Dacor DHI361 Instrukcja Użytkownika Strona 9

  • Pobierz
  • Dodaj do moich podręczników
  • Drukuj
  • Strona
    / 16
  • Spis treści
  • BOOKMARKI
  • Oceniono. / 5. Na podstawie oceny klientów
Przeglądanie stron 8
7
in s T a l l a T i o n in s T r u C T i o n s
WARNING
Donotinstalltherangehoodunlesstheelectrical•
serviceprovidedmeetstherangehoodspecifications.
Observeallgoverningcodesandordinancesduring•
planningandinstallation.Contactyourlocalbuilding
departmentforfurtherinformation.
Aqualifiedtechnicianmustcompletetheinstallation•
ofthisbuilt-inappliance.Theownerisresponsibleto
makesurethehoodisproperlyinstalled.
Toavoidanelectricshockhazardandproperty•
damage,locateelectricwiresandwaterpipesand
avoiddrillinginthevicinity.
Therangehoodisheavy.Topreventpersonal•
injuryandpropertydamageinstallthehoodonlyas
specifiedbelow.Makesureallscrewsusedtomount
andassemblethehoodaretight.
el e c t r i c Se r V i c e in S t a l l a t i o n
The electrical connection box must be:
Connectedtoa120Vac,60Hzdedicated,grounded,•
circuitprotectedbya15Ampcircuitbreakerortime
delayfuse.
Locatedaminimumof17”(43.2cm)abovethebottom•
oftherangehood.
mo u n t i n G Br a c k e t in S t a l l a t i o n
Locatethemountingbracketandpositionitagainstthe1.
ceilingatthepreviouslydeterminedmountinglocation
(seepage5).
Usingapencil,markthefourmountingholelocations2.
ontheceiling.
Drillfour1/16”(1.6mm)pilotholesatthemounting3.
holelocations.
Attachthebracketusingfour#12screws(not4.
supplied).Makesurethescrewspenetrateintothe
woodmountingsurfaces11/2”(3.8cm).
aS S e m B l e t h e ho o D
WARNING
Liftingandhangingtherangehoodrequirestwo•
people.Donotattempttoliftthehoodwithout
assistance.
Placethehoodassemblyonasoftsurfacewiththe1.
bottomsidedownduringassemblytoavoiddamage.
Tipthehooduponit’ssideandremovethefilter(s)to2.
reduceweightandavoiddamage.
Insidetheexhaustoutlet(s)therearemetalorplastic3.
damperflaps.Theflapsclosetohelppreventback-
draftswhenthebloweristurnedoff.Makesureallthe
flapsopenandclosefreelybeforeproceeding.Remove
anyshippingtapethatmaybepresent.
Removethetapethatholdsthewiringinplaceontop4.
ofthehoodduringshipment.
Onmodelswithtwoblowers:Puttheexhaustcowling5.
overthebloweroutletsonthetopofthehood.Fasten
thecowlinginplacewith14machinescrews.
Przeglądanie stron 8
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Komentarze do niniejszej Instrukcji

Brak uwag